Montana Plastic Primer is the perfect pre-treatment for plastic surfaces. After priming and drying, plastic surfaces can be painted with Montana sprays that have a synthetic, acrylic, or nitro-combination base. Can be used with the following types of plastic: polypropylene rubber, modified (EPDM), Acrylic Butadiene Styrene Plastics (ABS), Glass-Fibre Reinforced Plastics (GfK), Hard Polyvinyl Chloride (Hard-Pvc), Polyurethane (PUR), Polystyrene (PS), Polyamide (PA). It is recommended to test before use. Drying time varies depending on temperature and humidity and may take a few hours.
Montana DUSTCLEAN spray is a compressed aerosol spray for the easy removal of dust and loose dirt from sensitive or hard to reach surfaces, using high pressure. This spray can also be used to clean objects prior to final sealing - with varnish for example. The strong, direct spray output cleans effectively, perfect for interior use. The highly-pure and dry DUSTCLEAN spray leaves no residues. Do not use on electronic devices.
Montana ACETONE spray is a universal thinner and cleaning agent that is transparent in color. Removes residues of paint, lacquer, silicone, wax, tar, de-greasing. Suitable for pre-treatment before painting objects or to remove paint residues after painting. Can be used on porcelain, glass, ceramics, blank metals and others . Evaporates quickly without leaving residues. Non-corrosive. Always test spray on a non-visible area to check for any reactions to lacquer or paint, especially when used on plastic grounds as it may etch synthetic surfaces. Can be used as CAP CLEANER - put used nozzles on the ACETONE CAN and clean by spraying. USE: Test spray on a non-visible area to check for any reactions to lacquer or paint.
Pollution free etching spray for most usual types of lacquer. Montana REMOVER spray dissolves and removes lacquers quick and thoroughly. Do not use on cars! Application is possible on many surfaces such as, walls, clay bricks, stone, concrete surfaces, marble, asphalt, glass, metal and wooden surfaces. It becomes a gel-like consistency, to keep from running off vertical surfaces. Application on non-ferrous metals might cause discoloration. Content is ph-neutral.
USE: Surfaces should be dry, clean of dust, oils and rust before paint application. Check the firmness and stability of the basic color on painted or lacquered grounds at an inconspicuous spot. Sensitive areas, which you do not want to treat, should be covered carefully with a protective sheeting. Spray generously and let act for approx. 10 - 15 minutes. Depending on quality and age of the paint you want to remove, the acting time can be shortened or extended up to 24 hours. Then scrape off with a suitable tool. If necessary, wash off with cellulose nitrate dilutent or just with water. In case of very porous grounds, use a wire brush. If necessary, repeat the procedure. Before application of new paint, all residues of Montana REMOVER have to be removed.
Acid-free, quick drying, clear varnish made of acrylic base. No yellowing or de-saturation. For interior and exterior use. Can be used for art, hobby, crafts and DIY. Available in gloss, semi-gloss, matte finish. Gloss level shown on donut (see top of can). Protects and fixes paint on surfaces like canvas, paper, charcoal drawing, bast fibre, wood, photos, etc. Protects against oxidation. During application, protect the object and the surrounding area from spray. Surfaces should be dry, clean of dust, oils and rust before applying the varnish.
Shake can well for 2-3 minutes upside down to take advantage of gravity. Remove the safety ring by removing the nozzle and turning the can upside down allowing it to fall out. Then re-apply the nozzle. Apply varnish in several thin layers, spraying before the previous coat is fully dry but with 2 minutes between each pass. Further coats might require a drying time of 24 hours or more depending on substrate. For optimal lifespan, always store cans with the nozzle on. NOT COMPATIBLE WITH SYNTHETIC BASE LACQUERS. Always test spray on a non-visible area to check compatibility of lacquer or paint.