or cancel
  1. Zortrax M200 3D Printer Update

    08:18

    from Steve Talkowski / Added

    192 Plays / / 0 Comments

    Some latest 3D printing results with the Zortrax M200.

    + More details
    • Silhouette Bots - Periscope Edition

      17:17

      from Steve Talkowski / Added

      32 Plays / / 0 Comments

      Had a few spare moments to show some more examples of quickly cranking out concept bots using SketchBook Pro and the symmetry tool.

    • Zortrax M200 Time-Lapse

      00:12

      from Steve Talkowski / Added

      61 Plays / / 0 Comments

      This is the start is a 1d 3hr 31m test print just started an hour 1/2 ago. That base is 4.9" in diameter the height of this #ZBrush bust sculpt will be 120mm/4.725 inches. Layer thickness set…

    • 3D Micro Partial Print Failure

      01:03

      from Steve Talkowski / Added

      38 Plays / / 0 Comments

      So here's something interesting. I get a successful raft laid down, and what appears to be a first layer of filament that outlines what I think should be printing properly. However, the model…

    • The Micro 3D - Bent Axis Rods?

      00:43

      from Steve Talkowski / Added

      73 Plays / / 0 Comments

      I noticed this during an early bed calibration test. A slight waver on the X-Axis due to what appears to be bend axis rods? I don't know if this is normal or not, so am posting to share with…

    • 3D Printer Software Blues

      06:03

      from Steve Talkowski / Added

      97 Plays / / 0 Comments

      I hope to shed some light on how NOT to program your 3d printer software for the dumbed down masses. Let’s stick to some standardization in the 3d realm.

      + More details
      • Zortrax- Extruder not loading properly

        01:31

        from Steve Talkowski / Added

        59 Plays / / 0 Comments

        Alight, I cleaned the chunk of plastic from the cog and am attempting to reload the filament. It goes through the first part, then starts to skip, like the filament has hit a snag. I don't know…

      • Zortrax- filament stuck on extruded gear

        00:16

        from Steve Talkowski / Added

        76 Plays / / 0 Comments

        How do I go about removing this?!

      • Zortrax Extruder Not Pulling Filament

        03:06

        from Steve Talkowski / Added

        46 Plays / / 0 Comments

        So, after unloading and reloading the filament, I'm attempting to get a first print test done. Now, the extruder itself is not pulling the filament through. I can feel it making a stepping motion,…

      • Zortrax Test Print Error - No Filament

        03:43

        from Steve Talkowski / Added

        69 Plays / / 0 Comments

        Ok, after doing a manual calibration, I tried to print one of the provided models that would only take 25 minutes. Lots of banging and grinding noises, followed by the extruder going through the motions,…

      • Zortrax Bed Calibration Error

        02:36

        from Steve Talkowski / Added

        79 Plays / / 0 Comments

        Having issues with first time auto calibration. HELP!

      • Silhouette Bots

        14:21

        from Steve Talkowski / Added

        188 Plays / / 3 Comments

        Just wanted to show how easy it is to crank out some concepts using SketchBook Pro and the Symmetry tool.

        + More details

        Browse Videos

        Steve Talkowski

        Here are all of the videos that Steve Talkowski has uploaded to Vimeo. Appearances are videos that Steve Talkowski has been credited in by others.

        Also Check Out